Home
Products
About Us
Factory Tour
Quality Control
Contact Us
Request A Quote

Sales & Support:sales@china-item.com

What a Cap Gauge Cannot Judge: Flash, Sink, Weld Line and the Cosmetic Boundary

Home News

What a Cap Gauge Cannot Judge: Flash, Sink, Weld Line and the Cosmetic Boundary

Good quality IEC/EN 60065 Standard for sales
Good quality IEC/EN 60065 Standard for sales
Our goods has safely arrived at our residence. Thank you for your excellent services. I hope we can cooperate again in the future.

—— Wira

I'm Online Chat Now
Company News
What a Cap Gauge Cannot Judge: Flash, Sink, Weld Line and the Cosmetic Boundary

Ask a quality engineer what a cap gauge proves and the honest answer is narrower than most inspection plans assume: it proves that certain dimensions lie between a go limit and a not-go limit. It says nothing about whether the cap will hold its shape at 200 degrees C, whether the cement will creep, or whether the flash along the thread will still be there after the first insertion. Those are separate questions with separate evidence, and confusing them is how a batch passes inspection and fails in a luminaire.

What the gauge is allowed to decide

IEC 60061-1 fixes the cap dimensions and IEC 60061-3 fixes the gauges that check them, in the 7006 sheet series. A pair such as 7006-27C-1 and 7006-28A-1 on an E27 cap checks the thread against a go and a not-go limit; the not-go member is the one that catches a thread cut too deep or too shallow. Both members answer a question about the metal or the moulding at 20 degrees C, and neither knows anything about the material behind the dimension.

The boundary is worth stating plainly. A gauge decides: thread form within limits, shell diameter, contact position, overall length where a sheet covers it. A gauge does not decide: surface finish, flash, sink, weld line, cement fill, solder quality, plating thickness, or behaviour at temperature.

Where visible defects sit

DefectGauge verdictJudged by
Flash on the thread flankUsually passes; only blocks entry when heavyDrawing limit and a stated viewing condition
Sink mark on the shellAlways passesCosmetic standard, not dimensional
Weld line across the shellPasses unless it distorts the formMechanical test: torque and impact
Short moulding at the thread startCaught, if the flaw reaches the go limitGauge, plus entry depth record
Ovality of the shellCaught, by the not-go memberGauge
Cement not fully curedInvisible to the gaugeTemperature and torque test

How much flash is too much

A limit that says clean threads with no flash is not a specification, it is an aspiration, and it will be reinterpreted differently on every shift. A workable limit is numeric and bounded in area: flash permitted up to 0.2 mm proud of the flank, and no single flash area larger than about 1 square millimetre within the first 5 mm of thread engagement. That is enough to keep a mould running and narrow enough that two inspectors reach the same verdict.

The viewing condition has to be written down as well. A defect seen at 300 mm under 500 lux is a different defect from the same one seen at 150 mm under 1000 lux. Specify the distance, the illuminance and the viewing angle, and the argument about cosmetics disappears in most audits.

The defects that pass a gauge and fail in service

Three of them account for most field returns on caps that passed inspection:

  • Cement creep. The shell is dimensionally perfect and the cap turns on the bulb under heat. The gauge cannot see cement fill or curing; only a temperature and torque test can.
  • Solder voids on the contact. The contact sits at the right height and still overheats, because the joint behind it is porous. This is a cross-section or a temperature rise finding, not a gauge finding.
  • Plating porosity. A nickel finish within thickness limits can still be porous enough to corrode in a damp luminaire, and the failure appears months after installation.

Each of these has its own article on this site, and each of them belongs in the inspection plan next to the gauge check rather than in place of it: cement creep explains the turning cap, and solder resistance covers the joint behind the contact.

Writing an inspection plan that holds up

The sequence that works puts the gauge first because it is fast and objective, then the cosmetic check against a written limit, then the destructive or thermal checks on a sample. Record the gauge result as a number where possible — entry depth in millimetres, not just pass — because the depth is the trend that predicts wear. Keep the cosmetic limit on the drawing the operator actually holds, not in a quality manual nobody opens.

For the artefacts themselves, the lamp cap gauge range lists the 7006 sheets against cap types so the plan can name the right pair for each cap family.

Pub Time : 2026-11-16 09:00:00 >> News list
Contact Details
SHENZHEN JULIXING INSTRUMENTS CO., LTD.

Contact Person: Mr. Eason Wang

Tel: 86-755-33168386

Fax: 86-755-61605199

Send your inquiry directly to us (0 / 3000)