Home
Products
About Us
Factory Tour
Quality Control
Contact Us
Request A Quote

Sales & Support:sales@china-item.com

Thread Gauge Wear: The 0.01 mm That Turns a Good Cap Into a Reject

Home News

Thread Gauge Wear: The 0.01 mm That Turns a Good Cap Into a Reject

Good quality IEC/EN 60065 Standard for sales
Good quality IEC/EN 60065 Standard for sales
Our goods has safely arrived at our residence. Thank you for your excellent services. I hope we can cooperate again in the future.

—— Wira

I'm Online Chat Now
Company News
Thread Gauge Wear: The 0.01 mm That Turns a Good Cap Into a Reject

Thread gauges for lamp caps are simple in form and demanding in tolerance. A go ring is a short thread with a defined pitch and a defined depth; a no-go ring is the same thread at the other limit. Both wear, and both wear in the direction that makes the test easier to pass.

The result is a cap that passes the gauge and falls out of the holder, or one that passes and arcs because the thread is loose enough to move.

How much wear is too much

The tolerance band on an E27 thread is a few tenths of a millimetre across the major diameter. A gauge that has consumed a tenth of that band is at the point where the operator can no longer feel the difference between a good cap and a marginal one.

GaugeWear directionEffect on the test
Go ring, major diameterGrowsAccepts caps that are under size
No-go ring, major diameterGrowsAccepts caps that are over size
Thread depthShallowsAccepts caps with too little thread
Pitch, cumulativeStretchesAccepts caps with a wrong lead
Ring surfacePolishes, then gallingInsertion force changes, judgement becomes force-based

Every row moves the verdict towards acceptance. There is no wear direction that makes a gauge stricter, which is why a worn gauge set is worse than no gauge set.

Keeping the number under control

  • Measure the go ring with a setting plug. Thread measuring wires or a thread micrometer, calibrated against a master.
  • Check insertion torque, not just fit. A ring that screws on with two fingers has lost its meaning.
  • Replace, do not re-lap. Lapping a thread ring changes the pitch line and the form together.
  • Retire on count. A ring used in production reaches its limit in months, not years.

The gauge sheet is the specification

IEC 60061-3 defines each gauge with a sheet number, and the sheet carries the dimensions, the thread form and the acceptance rule. A gauge without its sheet number is a piece of hardened steel with a thread, and its readings cannot be defended in a dispute.

Our lamp cap gauges are supplied with the sheet number stamped on the body, and the technical notes explain how to read the sheet without guessing which dimension is the working one.

Standards referenced: IEC 60061-3 (gauges), IEC 60061-1 (caps), ISO 1502 for thread gauge practice.

Two readings per gauge per quarter

Measure the go ring at the major diameter and the thread depth, and write both numbers beside the gauge number. Two readings, 10 minutes, and the trend becomes visible after the second quarter: a ring losing 0.003 mm per quarter crosses a 0.01 mm allowance in 3 quarters, long before the annual calibration.

Insertion torque is the second check: a ring that screws on with two fingers has already lost its meaning.

复检时的三个读数:大径、中径、牙深,各测 3 个截面取最差值。中径用三针法测得,量针直径按 0.577P 选取,E27 的螺距 3.629 mm 对应量针约 2.09 mm,这一支量针本身也要有 1 µm 级的证书。

Pub Time : 2026-11-18 09:00:00 >> News list
Contact Details
SHENZHEN JULIXING INSTRUMENTS CO., LTD.

Contact Person: Mr. Eason Wang

Tel: 86-755-33168386

Fax: 86-755-61605199

Send your inquiry directly to us (0 / 3000)