Home
Products
About Us
Factory Tour
Quality Control
Contact Us
Request A Quote

Sales & Support:sales@china-item.com

How to Read a 60061 Gauge Sheet: 7006-xx-1, -2 and -3 Mean Three Different Things

Home News

How to Read a 60061 Gauge Sheet: 7006-xx-1, -2 and -3 Mean Three Different Things

Good quality IEC/EN 60065 Standard for sales
Good quality IEC/EN 60065 Standard for sales
Our goods has safely arrived at our residence. Thank you for your excellent services. I hope we can cooperate again in the future.

—— Wira

I'm Online Chat Now
Company News
How to Read a 60061 Gauge Sheet: 7006-xx-1, -2 and -3 Mean Three Different Things

A gauge sheet looks like a mechanical drawing with a sheet number in the corner. The number is the important part: the 7006 series covers E27 and E26 gauges, and the suffix decides whether the drawing shows the gauge itself or one of the two acceptance conditions.

Reading the wrong sheet is not a small error. It can turn a no-go condition into a go condition and pass every bad cap in the batch.

The three variants

SuffixWhat the sheet showsWhat it is used for
-1The gauge as a physical object: dimensions, thread, materialManufacturing and purchasing the gauge
-2The "go" condition: gauge fully engaged with a conforming capJudging whether the cap reaches full insertion
-3The "no-go" condition: the limit of engagement for a non-conforming capJudging whether the thread is too large or too shallow
RelatedHolder gauges in the same familyChecking the holder, not the cap

The -2 and -3 sheets do not define new hardware; they define how far the same hardware may engage. That is why a workshop can own one gauge and still need both sheets on the wall.

Reading one sheet properly

  • Find the sheet number on the gauge, not in the catalogue. A gauge in the wrong box is a wrong gauge.
  • Identify the datum. Most cap sheets datum on the cap face or the contact, and engagement is measured from there.
  • Read the notes, not only the dimensions. The notes carry the condition: hand tight, no force, specified torque.
  • Check the revision letter. Sheets are amended, and an old printout describes an old gauge.

Why the engagement condition is the real test

A cap can be dimensionally correct and still fail in service if it screws in only three turns instead of four. The -2 condition defines those turns as a geometric relationship, not as a count, which is why the gauge is a better instrument than a visual check.

Our cap gauge sets are supplied with the relevant -1, -2 and -3 sheets, and the technical notes walk through a worked example for the E27 family.

Standards referenced: IEC 60061-3 (gauge sheets 7006-xx), IEC 60061-4 (guidance and gauge use), IEC 60061-1 (cap dimensions).

The three questions to ask before using a gauge

Which sheet number is stamped on the gauge, which revision letter does the sheet carry, and which condition (-2 or -3) applies to this inspection. Answering the three takes 2 minutes and prevents the most expensive mistake in cap inspection: passing a batch with the no-go condition.

  • Keep the current revision of each sheet with the gauge, not in a folder.
  • Retire superseded prints the day the new revision arrives.
  • Record the sheet revision in the inspection record.

图纸上的公差通常写成上下偏差,例如大径 26.95 mm 至 27.05 mm,中间的 0.1 mm 就是判定的全部余地。量规本身按 10 % 的制造公差带制作,即 0.01 mm,所以量规磨损 0.01 mm 就已用尽它的份额。

Pub Time : 2026-11-18 09:00:00 >> News list
Contact Details
SHENZHEN JULIXING INSTRUMENTS CO., LTD.

Contact Person: Mr. Eason Wang

Tel: 86-755-33168386

Fax: 86-755-61605199

Send your inquiry directly to us (0 / 3000)