Home
Products
About Us
Factory Tour
Quality Control
Contact Us
Request A Quote

Sales & Support:sales@china-item.com

Go and No-Go on the Same Gauge: Reading the Step, Not the Gap

Home News

Go and No-Go on the Same Gauge: Reading the Step, Not the Gap

Good quality IEC/EN 60065 Standard for sales
Good quality IEC/EN 60065 Standard for sales
Our goods has safely arrived at our residence. Thank you for your excellent services. I hope we can cooperate again in the future.

—— Wira

I'm Online Chat Now
Company News
Go and No-Go on the Same Gauge: Reading the Step, Not the Gap

Most dimensional inspection asks a question with two answers. A combined go/no-go gauge asks the same question twice, at two sizes, and the interesting outcome is not pass or fail but which of the two the part reached. Reading that correctly turns a binary inspection into a trend, and the trend is what tells you the tool is wearing out.

What the two diameters are for

The go end is the smallest acceptable feature: if the part will not accept it, the feature is undersized. The no-go end is the largest acceptable feature: if the part accepts it, the feature is oversized. A conforming part accepts the go end and refuses the no-go end. That is the whole rule, and it is the reason a gauge with only one end is not a gauge but a limit.

The distance between the two is the tolerance. On a lamp cap gauge to IEC 60061-3 the two ends can be 0.05 mm apart, which is smaller than the thermal expansion of the gauge over a 10 K shift. That is not a design flaw; it is why the gauges are used at a controlled temperature and why they are checked against a setting ring at intervals.

ObservationMeaningAction
Accepts go, refuses no-goWithin tolerancePass
Refuses goFeature undersizedReject, check the tool for wear first
Accepts go and no-goFeature oversizedReject, check the part process
Accepts go with a loose fitNear the upper limitPass, but watch the trend
Refuses go on some parts onlyProcess spread, not toolChart the parts, not the gauge
Gauge feels different after cleaningResin or oil film removedRe-baseline, then re-check the setting ring

The habit that makes gauges last

A gauge is checked against a setting ring or a master at the start of each shift, not each month. The check takes under a minute and catches the two failures that matter: wear that has moved the go end toward the no-go, and damage that has moved either end at all. A gauge that fails the ring check is removed from service immediately, because every part it has approved since the last good check is suspect.

The direction of wear is predictable: the go end wears first because it enters every part, and it wears toward the rejection side, which means the gauge slowly starts accepting undersized parts. That is the dangerous direction, because it produces escapes rather than false rejects, and escapes are only discovered downstream.

Recording which end failed

A inspection sheet with a single pass column throws away the most useful information in the process. Two columns, one per end, costs nothing and gives a distribution: parts that fail the go end are undersized, parts that fail the no-go end are oversized, and a mix of both means the process spread is wider than the tolerance rather than shifted.

  • Go failures trending up: tool wear on the forming die, or material lot change.
  • No-go failures trending up: the same die wearing in the other direction, or a mould temperature shift.
  • Both ends failing on the same batch: incoming material, not the tool.
  • No failures at all over a long run: verify the gauge is still capable before celebrating.

Standards referenced: IEC 60061-1 (lamp caps), IEC 60061-3 (gauges), ISO 14253-1 for the decision rules that turn a reading into a verdict.

把数字记下来,趋势才有意义

一只钢质量规在正常使用下的磨损速率大约是每 1,000 次插入 0.5 到 2 微米。若每天判 200 件,一个月 4,000 次,一年就是 2 到 10 微米——正好是一只 0.05 mm 台阶规的关键区间。这不是危言耸听,而是为什么"每季度用设定环复核一次"比"每年送校一次"更实用:年校只能告诉你已经超了多少,季度复核能在超之前拦住。

复核用的设定环(setting ring)本身也要有溯源。环的直径公差通常控制在 2 微米以内,且每两年送校一次;如果环本身磨损了 3 微米,所有被它"校准"的量规都会系统性地偏松,而且偏得一致,看不出异常。

三个可以立刻用上的数字

  • 量规与工件同温静置 30 分钟,室温 20 ± 2 ℃;一只 50 mm 的钢规在 3 K 偏差下长度差约 1.6 微米。
  • 每次班前用设定环复核,读数偏差超过 2 微米即停用,不要"再用一天看看"。
  • 台阶面平行度用塞尺四向检查,四向差超过 0.02 mm 即送修;这是判定翻转最常见的物理原因。
Pub Time : 2026-11-20 09:00:00 >> News list
Contact Details
SHENZHEN JULIXING INSTRUMENTS CO., LTD.

Contact Person: Mr. Eason Wang

Tel: 86-755-33168386

Fax: 86-755-61605199

Send your inquiry directly to us (0 / 3000)