Home
Products
About Us
Factory Tour
Quality Control
Contact Us
Request A Quote

Sales & Support:sales@china-item.com

Gauge Sheet Revision Control: When a 7006 Number Changes

Home News

Gauge Sheet Revision Control: When a 7006 Number Changes

Good quality IEC/EN 60065 Standard for sales
Good quality IEC/EN 60065 Standard for sales
Our goods has safely arrived at our residence. Thank you for your excellent services. I hope we can cooperate again in the future.

—— Wira

I'm Online Chat Now
Company News
Gauge Sheet Revision Control: When a 7006 Number Changes

A lamp cap gauge is defined by a sheet, not by a catalogue number. The sheet carries a figure, dimensions with tolerances, and a revision suffix. When the sheet is revised, the gauge in the gauge room does not change, its calibration certificate does not change, and nothing on the shop floor looks different — but the question it answers may have.

Anatomy of a gauge sheet designation

A designation such as 7006-27D-3 has three parts, and each carries information an inspector needs:

  • 7006 — the series, which identifies gauge sheets for lamp caps within IEC 60061-3.
  • 27D — the sheet identity, which ties the gauge to one cap family and one purpose. Different letters in the same number range are different gauges, not revisions of each other.
  • 3 — the revision of that sheet.

The distinction between a letter change and a number change is the part that causes mistakes. 27D and 27E are two different gauges; 27D-2 and 27D-3 are the same gauge at two revisions of the sheet. Buying "the latest 27D" gets the current revision; buying "27E" because it looks similar gets the wrong instrument.

The sheet number itself is not a serial. It is allocated in blocks that follow cap families, and the family is stated on the sheet: a 7006-27 series gauge checks an E26 cap whose thread is nominally 26 mm across, and a 7006-10 series gauge covers a B22 bayonet cap whose shell is 22 mm. The correspondence is not arithmetic — the E14 gauges sit in a different block — so the number has to be read from the sheet, not guessed from the thread size.

What a revision can change

Revisions are not editorial. In practice they do one of four things:

  1. Tighten a tolerance on a dimension, usually following a change in the cap standard.
  2. Add or remove a feature, such as a contact-making probe or a step that checks a specific cap variant.
  3. Correct an error in the previous sheet, which can move a dimension by more than the tolerance itself.
  4. Extend coverage to a new cap variant that did not exist when the sheet was written.

Only the third changes what an existing gauge measures. The first two change what a compliant gauge should be, and the fourth means the old gauge cannot check the new part at all. Put a number on it: on a cap whose thread limits are held to a few hundredths of a millimetre, a revision that moves a limit by 0.02 mm is the difference between a cap that passes and one that does not, and the gauge that measured it last month still reports the old answer.

The audit question that exposes the gap

"Show me the sheet this gauge was made to." A gauge with a certificate that says "in accordance with IEC 60061-3" and no revision number cannot answer it. Three records close the gap:

  • The gauge identification, engraved on the body, matching the sheet designation including revision.
  • The revision of the sheet in force at the date of manufacture, recorded on the certificate.
  • The current revision of that sheet, recorded at each calibration, with a note of whether they match.

When they do not match, the decision is not automatic. A gauge to revision 2 checking a cap that has not changed since revision 1 is still valid; a gauge to revision 2 checking a cap defined at revision 3 is not.

Managing a mixed gauge room

Most gauge rooms end up with a mixture of revisions, because gauges outlive standards. A workable policy has four parts:

ClassifyMark each gauge with its sheet revision, physically, not only in a database
MapRecord which cap variants each revision covers, so a superseded gauge is used only where it is still valid
ReviewCheck the sheet revision at every calibration, and again whenever a new cap variant is introduced
RetireWithdraw a superseded gauge when the parts it covers are no longer produced, and record the date

Why "it still passes calibration" is not enough

Calibration answers a narrow question: does this gauge still match the dimensions on the sheet it was made to? It does not answer whether that sheet is the right one. A gauge can be perfectly calibrated to a superseded sheet and still be the wrong instrument for the parts now being produced.

This is the same logic that applies to any limit gauge, and it is worth stating in the procedure: calibration confirms the instrument, not the specification.

Records that survive an audit

  • Gauge identity and sheet designation, including revision, on the gauge and in the register.
  • Certificate showing the sheet revision and the measured dimensions, not only pass or fail.
  • A revision history for each sheet in use, with the date the change was noted and the action taken.
  • A list of gauges that are superseded and the parts they are still permitted to check.

The lamp cap gauge range lists gauges by 7006 designation and sheet revision; the catalogue home indexes the lampholder gauges used alongside them.

Pub Time : 2026-11-16 09:00:00 >> News list
Contact Details
SHENZHEN JULIXING INSTRUMENTS CO., LTD.

Contact Person: Mr. Eason Wang

Tel: 86-755-33168386

Fax: 86-755-61605199

Send your inquiry directly to us (0 / 3000)