Home
Products
About Us
Factory Tour
Quality Control
Contact Us
Request A Quote

Sales & Support:sales@china-item.com

G13 Bi-Pin: The 12.7 mm Pitch and the Two Dimensions That Decide Fit

Home News

G13 Bi-Pin: The 12.7 mm Pitch and the Two Dimensions That Decide Fit

Good quality IEC/EN 60065 Standard for sales
Good quality IEC/EN 60065 Standard for sales
Our goods has safely arrived at our residence. Thank you for your excellent services. I hope we can cooperate again in the future.

—— Wira

I'm Online Chat Now
Company News
G13 Bi-Pin: The 12.7 mm Pitch and the Two Dimensions That Decide Fit

Bi-pin caps look like the easy case: two pins, one distance, one diameter. They are also the cap type where a lamp can pass every dimensional check and still not seat, because the two pins are checked separately and the pair is what has to fit.

The pitch is the dimension that carries the mechanical load, and it is the one most often taken on trust.

The dimensions that matter

FeatureNominalWhat it controls
Pin pitch12.7 mm centre to centreEngagement in the holder slots
Pin diameterAbout 2.4 mm for G13Grip and contact pressure
Pin lengthAbout 7.5 mm from the cap faceDepth of engagement before the cap bottoms
Pin parallelismBoth pins square to the cap faceSeating without skew
Cap face flatnessFlat within a small fraction of a millimetreBoth pins engage together
Pin tip formRounded or chamferedEntry into the holder without shaving

The 12.7 mm pitch is a fixed dimension in the cap sheet, and it is checked with a gauge that has two holes or two slots at that spacing. A lamp whose pins are each within diameter but 0.3 mm too far apart will enter one slot and bind on the other, and no single-pin check will find it.

Why pin length and pitch interact

If the pins are short, the lamp seats deeper before the contacts engage, and the cap face touches the holder before the pins are fully home. If the pins are long, the lamp stands proud and the light centre is in the wrong place. Both cases look like a pitch problem to an operator, and neither is.

The parallel condition is the third variable. Two pins that are each square but not parallel to each other force the lamp to skew as it enters, which loads one pin and leaves the other loose. That is the failure mode that produces intermittent starting in a fluorescent fixture, and it is invisible to a diameter gauge.

Checking a batch

  • Pitch with a gauge, not a caliper. A caliper on two small pins measures the outside faces and includes the pin diameters, so the reading is pitch plus diameter, and the operator has to subtract.
  • Diameter with a micrometer in two planes. A pin that has been flattened in handling reads correct in one plane.
  • Length from the cap face, not from the end of the glass.
  • Squareness with a dial indicator while the cap is rotated in a vee block.

Handling damage is the main cause of failure

Bi-pin lamps are packed in sleeves and handled by the glass. A pin bent by 0.2 mm during packing is a lamp that will fail in the fixture and pass a diameter check, because the bend is at the root and the tip is still round. Inspect for bend at the root with a magnifier, and treat any lamp that has been dropped as suspect regardless of its dimensions.

For the gauge itself, check the pitch every few months with a setting plug: two hardened pins at 12.7 mm, used as a master. A gauge whose holes have worn oval will accept an out-of-pitch lamp and the trend will be invisible until a customer complains. A G13 bi-pin gauge with a master setting plug is the practical kit, and the site index lists the cap gauges by sheet number.

Standards referenced: IEC 60061-1; IEC 60061-3.

Pub Time : 2026-11-17 09:00:00 >> News list
Contact Details
SHENZHEN JULIXING INSTRUMENTS CO., LTD.

Contact Person: Mr. Eason Wang

Tel: 86-755-33168386

Fax: 86-755-61605199

Send your inquiry directly to us (0 / 3000)