Home
Products
About Us
Factory Tour
Quality Control
Contact Us
Request A Quote

Sales & Support:sales@china-item.com

E14 Gauges: Reading a Go and Not-Go Pair and the Two Dimensions That Reject a Cap

Home News

E14 Gauges: Reading a Go and Not-Go Pair and the Two Dimensions That Reject a Cap

Good quality IEC/EN 60065 Standard for sales
Good quality IEC/EN 60065 Standard for sales
Our goods has safely arrived at our residence. Thank you for your excellent services. I hope we can cooperate again in the future.

—— Wira

I'm Online Chat Now
Company News
E14 Gauges: Reading a Go and Not-Go Pair and the Two Dimensions That Reject a Cap

An E14 cap inspection looks like a two-step process: the go gauge should enter, the not-go gauge should not. That is correct and incomplete. The pair checks two different failure modes on two different features, and a cap can pass both and still be rejected at the next stage of assembly. Understanding what each gauge is for turns a pass/fail ritual into a diagnosis.

Start with what the designation means. In IEC 60061-3 the number in an Edison screw cap is the nominal thread diameter in millimetres: an E14 thread is 14 mm across, an E27 is 27 mm, and the two differ by 13 mm in diameter. The gauge pair does not measure that diameter directly. It brackets the cap between a maximum and a minimum, and both limits are on the sheet rather than in the designation.

What each gauge checks

Go gaugeConfirms the cap is not too large in the dimensions that must fit into a lampholder. It must enter and seat to the depth defined on the sheet.
Not-go gaugeConfirms the cap is not too small in the dimensions that must make contact and hold. It must not enter beyond the defined limit.
BothTogether they bound the cap between a maximum and a minimum, and that pair is the tolerance.

The go gauge protects the lampholder from damage and the assembly from a cap that will not fit. The not-go gauge protects function: a cap that is too small will not hold, will not make reliable contact, and may sit too deep or too shallow.

Why "seated to depth" is the real go criterion

A go gauge that enters a few turns and stops has not passed. The criterion is that the cap engages to the depth the sheet defines, which is what guarantees the cap will sit correctly in a lampholder. Two reasons a go gauge stops short even when the thread is nominally correct:

  • Thread start or lead error. The cap starts on the gauge and binds, so it cannot reach depth. The thread is the right size and the wrong shape.
  • Debris or damaged thread. Solder, plating or a burr in the thread prevents full engagement. This is a cap defect that the gauge correctly detects.

Recording how many turns were achieved before binding is more useful than a binary result. A cap that reaches 80 percent of depth consistently is a supplier tooling problem, not a random defect.

The not-go criterion and the cap that is too small

A not-go gauge is made at the minimum material condition. It must not enter the cap beyond a defined amount. If it does, the cap's internal feature is too large or too deep, which is the opposite of what the go gauge checks.

The failure this catches is a cap that fits loosely: it will assemble, it will often light, and it will fail in service through poor contact or through working loose. A 0.02 mm reduction in thread diameter is enough to turn a firm fit into a loose one, which is why the not-go side of the pair is not optional. This is the defect that a visual inspection cannot find and that only a not-go gauge detects.

Two more dimensions the pair does not cover

Contact position and insulation are checked by separate gauges, and this is where a cap that passed the go/not-go pair can still be rejected:

  1. Contact-making. A gauge with a defined contact probe checks that the cap's contact sits at the right height and presents the right surface. A cap whose thread is perfect but whose contact is recessed will not make reliable contact.
  2. Protection against accidental contact. A gauge checks that live parts are not accessible when the cap is inserted to a defined depth — a safety dimension, checked separately from the thread.

A gauge room that only holds the go/not-go pair is testing the thread and calling it a cap inspection.

Handling and care

A production line usually needs 3 gauges for one cap: go, not-go and contact-making. Running only the first 2 tests the thread in 2 directions and leaves the electrical interface unmeasured, which is why a cap that passes inspection can still fail on the assembly line.

  • Store gauges on a rack, not loose in a drawer. A gauge that has been dropped is a gauge that needs re-verification, not one that needs a wipe.
  • Clean with a soft cloth; never lap a gauge by hand to remove a mark. A few strokes of hand lapping remove 5 to 10 micrometres, which is more than the tolerance the gauge is working to.
  • Check for thread damage with a magnifier before each shift, especially the first two threads, which take the load.
  • Record the gauge identification with the result. A pass recorded without the gauge identity cannot be traced back when a batch is questioned.

Reading a rejection

Three outcomes are worth separating in a record, because they point at different fixes:

  • Go does not enter. Cap thread too large, damaged or badly started. Supplier tooling or handling.
  • Not-go enters. Cap thread too small or too deep. Supplier tooling, and a functional risk.
  • Both behave correctly but the contact gauge fails. Thread is fine, contact geometry is wrong. A different process in the same supplier.

The lamp cap gauge range lists E14 go, not-go and contact-making gauges by sheet number; the catalogue indexes the matching lampholder gauges.

Pub Time : 2026-11-16 09:00:00 >> News list
Contact Details
SHENZHEN JULIXING INSTRUMENTS CO., LTD.

Contact Person: Mr. Eason Wang

Tel: 86-755-33168386

Fax: 86-755-61605199

Send your inquiry directly to us (0 / 3000)