Home
Products
About Us
Factory Tour
Quality Control
Contact Us
Request A Quote

Sales & Support:sales@china-item.com

Cap Cement and the T-Mark: What 210 °C Does to the Joint Between Glass and Brass

Home News

Cap Cement and the T-Mark: What 210 °C Does to the Joint Between Glass and Brass

Good quality IEC/EN 60065 Standard for sales
Good quality IEC/EN 60065 Standard for sales
Our goods has safely arrived at our residence. Thank you for your excellent services. I hope we can cooperate again in the future.

—— Wira

I'm Online Chat Now
Company News
Cap Cement and the T-Mark: What 210 °C Does to the Joint Between Glass and Brass

A lamp cap is a composite: a brass shell or an aluminium one, a glass insulator, and a cement that joins them. The metal expands faster than the glass, and the cement has to absorb that difference over every switching cycle for the life of the lamp.

The T-mark on the lamp is the manufacturer declaring the maximum temperature at the cap. Above it, the cement softens, the shell rotates, and the lamp either falls out of the holder or shorts inside it.

What the temperature does

Cap temperatureCondition of the cementPractical consequence
Below 120 °CFirm, no movementNormal service for most domestic lamps
120 °C to 170 °CSlight softeningTorque resistance begins to fall
170 °C to 210 °CSoft, creepingCap rotates under the holder spring
Above 210 °CDecomposed or carbonisedLoss of insulation, smoke, failure
Cycling, any levelFatigue at the glass interfaceCrack after a few thousand cycles

The number in the T-mark is not a safety margin; it is a measured value with a test behind it. A lamp marked T210 has been tested at 210 °C at the cap for the specified time and found not to move.

Where the heat comes from

  • The lamp itself. A halogen capsule radiates directly at the cap in some designs.
  • The luminaire. A closed fitting raises the cap temperature by 30 K to 60 K over the open-air value.
  • Adjacent lamps. In a multi-lamp fitting the neighbour contributes.
  • Poor holder contact. A high-resistance contact adds watts at the cap, not in the lamp.

Testing the joint rather than the lamp

The mechanical check is a torque test at temperature: apply the specified torque to the shell while the cap is held at the T-mark value, and the joint must not rotate. The electrical check is insulation resistance between shell and contact after the same soak, because a decomposed cement becomes conductive before it becomes loose.

Both checks need the cap at temperature, which means a fixture that heats the cap without heating the joint unevenly. Our cap gauges and holders include the torque fixtures, and the technical notes cover the gauge sheets that define each cap form.

Standards referenced: IEC 60061-1 (caps and holders), IEC 60061-4 (gauge sheets), IEC 60432-1 for the T-mark declaration on incandescent lamps.

Why the mark is on the lamp and the test is on the cap

The T-mark is a lamp declaration, but it can only be met if the cap, the cement and the holder cooperate. A lamp marked T210 in a holder that runs 20 K hotter is a lamp that will fail its own declaration.

  • Check the holder temperature, not only the lamp.
  • Test at the marked value, not 20 K below it.
  • Repeat after 100 cycles: the cement fatigues before it softens.

Numbers to work with: a 60 W lamp in a closed fitting raises the cap 40 K above ambient, a typical phenolic cement softens at 180 °C, and the torque check is usually 1 N·m for 1 min at the marked temperature. After 100 thermal cycles the same joint typically loses 30 percent of its holding torque.

Pub Time : 2026-11-18 09:00:00 >> News list
Contact Details
SHENZHEN JULIXING INSTRUMENTS CO., LTD.

Contact Person: Mr. Eason Wang

Tel: 86-755-33168386

Fax: 86-755-61605199

Send your inquiry directly to us (0 / 3000)